KILZ 2 Latex is a fast drying, water-base multi-surface primer-sealer-stainblocker with excellent adhesion, sealing properties and very mild odor. KILZ 2 latex primer also blocks medium stains and provides a mildew resistant coating. KILZ 2 Latex Features: * Blocks medium stains * Hides previous colors well / Low Odor * Good adhesion and sealer * Mildew-resistant * Stains: water, rust, grease, ink, pencil and felt marker * Odors: pet, smoke * Use on: interior, drywall, woodwork, plaster, paneling, wallpaper, masonry, brick and painted metal
Warning: Cancer & Reproductive Harm: www.P65Warnings.ca.gov
Warning: Cancer & Reproductive Harm: www.P65Warnings.ca.gov
PRODUCT SPECIFICATIONS
| Base | Water |
| Int/Ext | Int/Ext |
| Color | White |
| Coverage - Low | 300 sq. ft. |
| Mils Wet | 5.3 |
| Mils Dry | 1.7 |
| Coverage - High | 400 sq. ft. |
| Mils Wet | 4 |
| Mils Dry | 1.3 |
| Finish @ 85o | < 10 |
| Min Application Temp | 50oF (10oC) |
| Max Application Temp | 90oF (32oC) |
| Dry To Touch | 30 min |
| Dry To Recoat | 1 hour |
| Max Tint | 2 oz |
| VOC | 96 g/L |
| Brush | Nylon / Poly |
| Roller - Smooth | 3/8" - 1/2" nap |
| Roller - Porous | 1/2" - 3/4" nap |
| Spray Tip | .015" - .021" |
| Spray Filter | 60 mesh |
| Spray Pressure | 2,500 - 3,200 |
| Volume Solids | 32.6% (+/-) 2% |
| Weight Solids | 48.1% (+/-) 2% |
| Viscosity | 95 - 105 KU |
| Flashpoint | N/A |
WHERE TO USE
Use on properly prepared interior and exterior surfaces, such as:
- Brick
- Painted Metal
- Properly Prepared Glossy Surfaces†
- Drywall
- Paneling
- Stucco
- Masonry
- Plaster
- Wood
SURFACE PREPARATION†
- The surface must be clean, free of dust, grease, wax, peeling paint and wallpaper paste. If washing is necessary, use a non-soapy detergent or a TSP substitute. Rinse well and allow to dry.
- For maximum adhesion, scrape off loose paint and scuff sand the surface thoroughly before priming. On glossy surfaces: scuff sand the surface thoroughly before priming.
- Unpainted, exterior wood exposed to sun and/or moisture longer than 2-4 weeks must be cleaned and sanded before priming.
- Wash the area with a mildew remover, rinse with water and allow to dry before priming.
- KILZ 2 may be used on clean, dry, aged masonry surfaces. New masonry must be allowed to cure (dry) at least 30 days before applying KILZ 2.
- It is critical to clean smoke damaged surfaces thoroughly before priming. Primary Recommendation: KILZ ORIGINAL or KILZ ODORLESS.
APPLICATION
- Eye protection is recommended.
- A small amount of water may be added for spray applications, but do not thin for stainblocking applications.
- Stir thoroughly before and occasionally during use.
- Apply using a brush, roller or sprayer.
- Only apply if surface, air and product temperatures are between 50°-90°F.
- Prime the entire surface to ensure a uniform appearance of the topcoat.
- After priming, test for stain bleed-through by applying the topcoat to a small section. If the stain bleeds through the topcoat, apply a second coat of primer and test again before topcoating the entire area. If bleeding continues, a longer dry time is needed before topcoating.
- Tinting is not recommended for stainblocking applications. KILZ 2 may be tinted with up to 2 ounces of universal colorant per gallon for non-stainblocking projects. Tinting to a lighter shade than the topcoat is recommended.
- Coverage is up to 300 square feet per gallon on porous surfaces; up to 400 square feet per gallon on smooth, nonporous surfaces.
DRY TIME at 77°F (25°C), 50% RH
CLEAN UP & DISPOSAL - Dries to the touch in 30 minutes.
- Can be recoated or topcoated in one hour with latex or oil-based paint.
- Application at lower temperatures, in high humidity or in poorly ventilated areas will affect dry time.
- Clean equipment and paint spatters with warm, soapy water.
- Dispose of contaminated absorbent, container and unused product in accordance with all current federal, state and local regulations.
- To recycle or properly dispose of paint or primer in your community, call 1-800-CLEANUP.
