Use Wolman Deck & Fence Brightener Wood Cleaner & Coating Prep (Liquid Concentrate) to clean and restore decks and other weathered exterior wood, or to prepare new wood surfaces before sealing or staining. A universal cleaner for all wood types, it is also formulated to remove stubborn black tannin stains from new cedar, redwood and exotic hardwoods.1 Gallon – makes 5 gals. solution; covers 750 sq. ft.
WOOD TYPES:
Use on all types of pressure-treated lumber,
Note: New generation (non-CCA) pressure-treated
Compatibility:
Chlorine free, 100% biodegradable – will not harm plant life, damage wood lignin or leave a bleached-out look.
Restores UV-grayed, dirty, mildew-stained wood surface to a bright, like-new appearance.
Fast and easy to use - mix with water in less than 1 minute, does the job in 10 minutes!
Mix 1 part product with 4 parts water, then apply by pump-style sprayer (with no aluminum parts), brush, mop or roller.
FOR EXTERIOR USE ONLY
Use to prepare or restore outdoor wood decks,
porches, fences, siding, shakes & shingles, outdoor
furniture & décor, boat docks, boardwalks, gazebos &
arbors, play sets and more.
Removes the Following Coating Barriers from weathered wood:
Removes the Following Coating Barriers from weathered wood:
Ground-In Dirt, Mildew, Mold & Algae Stains, Weathered Gray Surface,
Old Sealers & Clear Finishes
WOOD TYPES:
Use on all types of pressure-treated lumber,
plastic and wood composite materials, North
American hardwoods, exotic hardwoods
such as Mahogany, Teak, Ipé etc..
Note: New generation (non-CCA) pressure-treated
lumber, when initially installed may develop
pronounced mildew growth during the first few months
of weathering. To reduce or avoid mildew stain
ing allow wood to weather for 1 to 3 months before
applying a protective coating. To immediately protect
against water damage, prep the surface with
DeckBrite and pre-treat with Wolman RainCoat®Clear
Water Repellent–Oil-Base. Allow 6 months
Water Repellent–Oil-Base. Allow 6 months
before applying a protective coating.
Compatibility:
This product will clean but not remove oil or latex
stains and paints in sound condition. Care should be
taken to cover any exposed aluminum surfaces to prevent
discoloration, as this product is corrosive to metal. Once
dry, surfaces cleaned with this product may be coated with oil or
water-base water repellents, transparent finishes, colored
stains or paints.
Pre-rinse grass, plants and shrubs surrounding wood
Application:
On horizontal surfaces:
On vertical surfaces:
Brush or Pressure Wash:
Brush:
Pressure wash:
Rinse:
Recommended Number of Coats – Apply one (1) coat,
Mixing:
In a five gallon plastic bucket, combine one gallon concentrate
with four gallons water to make five gallons solution, enough to
clean/prepare approximately 750 sq. ft. Each gallon of solution
cleans approximately 150 sq. ft. If less than five gallons solution
is needed, use a plastic measuring device to combine one part
concentrate with four parts water. Stir for one minute or until
solution is thoroughly blended. Do not mix with any other
products. Rinse plants with water after exposure.
Pre-rinse grass, plants and shrubs surrounding wood
structure to be cleaned. Cover any exposed aluminum
surfaces to prevent corrosion. Sweep away surface dust, dirt
and debris. If the surface is hot to the touch or in direct
sunlight, dampen with fresh water to cool.
Application:
Apply when outside temperatures are between
40°F. and 90°F
Pre-wet surface with fresh water.
Pre-wet surface with fresh water.
Working on 20 sq. ft. at a time to maintain optimum surface
wetness, apply solution and let sit and foam for 10 minutes.
If solution dries prematurely, keep it wet with additional
solution as needed.
On horizontal surfaces:
Apply solution with a pump sprayer, airless sprayer,
brush, mop or roller.
On vertical surfaces:
Apply solution with a pump sprayer or deep-nap roller,
working from the bottom to the top of the
working from the bottom to the top of the
structure.
Brush or Pressure Wash:
Brush:
Briefly scrub surface with Wolman WOODWORX® Deck
Brush or other stiff, short-bristle brush, using moderate pressure.
Pressure wash:
Use a 40° tip and 1,500-2,500 PSI for pressure-treated wood
and hardwood, 500-1,000 PSI for Cedar and
and hardwood, 500-1,000 PSI for Cedar and
Redwood. Move lengthwise with boards to avoid cut marks
across grain. Either technique helps ensure old surface is entirely
removed.
Rinse:
If pressure washing is not employed. After brushing, rinse
thoroughly with a garden hose, using the highest pressure
nozzle setting available. On a vertical surface, continually
rinse brightened areas to avoid streaking. Rinse any wood
fibers off surrounding surfaces immediately. When dry,
wood surface should appear clean, bright and free of mildew
and algae stains.
Recommended Number of Coats – Apply one (1) coat,
and allow to sit for the entire recommended time of 10 minutes.
Heavily weathered, extremely dirty or badly stained areas may
require a second application.
CAUTION:
require a second application.
CAUTION:
Bare wood and/or coated surfaces can become slippery when wet.
Use caution when walking on wet surfaces.
Storage:
Precautions:
KEEP OUT OF REACH OF CHILDREN.
Compatibility:
Clean Up:
Clean tools and equipment after use with water.
Storage:
Store unused concentrate in the closed, original labeled container.
Precautions:
CONTAINS OXALIC ACID.
Causes eye irritation. Can cause skin irritation. Prevent contact with eyes and skin.
During preparation and application, wear rubber or PVC gloves
and safety goggles. Wash thoroughly after handling. May be
harmful if swallowed. Do not breathe spray mist. If applying
with a sprayer, wear a properly fitted, NIOSH-approved
respirator. Use only with adequate ventilation.
Do not mix with any other products, especially those containing
chlorine or bleach (sodium hypochlorite). Rinse plants with water
after exposure.
KEEP OUT OF REACH OF CHILDREN.
Compatibility:
This product will clean but not remove oil or latex stains and
paints which are in sound condition. This product is harmless to
most plant life as well as plastic, glass, Plexiglas, brick, aluminum
and vinyl siding, metal, concrete and caulked surfaces. Rinse
plants and surrounding surfaces with water after exposure. Once
dry, surfaces cleaned with this product may be coated with oil or
water-base water repellants, transparent finishes, colored stains
or paints.
