Water Born, Clear, High Build Filling Primer, VOC: less than 100 g/l• Fast drying, penetrating, filling primer for exterior applications • Ideal for rough surfaces, T111 Siding, Plywood, Stucco, Brick, • Can save hours of prep work • Remains flexible • Low temp, high humidity application • Soap and water clean-up • Top coat with exterior latex and elastomeric paints in 60 minutes • Tintable with water based tint colors Item Numbers Ending In the Letter "R" Are Sold Only By The Box and Usually Ship in 10 to 14 Business Days
Product Storage:
Spreading Rate
Surface Preparation:
Product Preparation:
Apply directly from the can, no thinning is required. If thinning is
desired, use XIM’s Latex X-Tender. If tinting is desired,
use up to 2 ounces of universal tint per gallon. Do not exceed
2 ounces of tint per gallon. It can also be tinted by adding small quantities
2 ounces of tint per gallon. It can also be tinted by adding small quantities
of the Top Coat latex paint (½ Pint per gallon) to provide
an opaque, guide coat. Mix or shake well before application.
Product Storage:
Not to exceed 110°F.
Spreading Rate
50 – 200 Square Feet per Gallon Depending on dry film thickness
Surface Preparation:
Be sure the surface is clean and dry, free from dust, grease,
wax, oil, and other surface contaminants. Clean with a
strong detergent, rinse and allow to dry. Remove all loose and
peeling paint. The surface should be a sound, stable
peeling paint. The surface should be a sound, stable
surface. Spot prime areas that require extra filling. The
moisture content of wood should be below 15% at application.
Moldy or mildewed surfaces should be scrubbed
Moldy or mildewed surfaces should be scrubbed
with a mixture of one part of household bleach and three
parts of water, then thoroughly rinsed with clean water and allowed to dry.
Rotted wood should be replaced.
NOTE: Peel Bond is not recommended for horizontal walking surfaces such as decks.
BRUSH:
ROLL:
SPRAY:
Clean Up:
Application:
Apply by synthetic fiber brush, synthetic roller or by spray.
Can be applied at temperatures as low as 40° F. It can also
be applied in high humidity conditions, up to 90% relative humidity.
Under standard conditions, 77° F and 50% RH, Peel Bond will dry to
touch in about 30 minutes. Thicker coats will take longer to dry. It can be
top-coated in 40-60 minutes, under normal conditions. Peel Bond goes
Under standard conditions, 77° F and 50% RH, Peel Bond will dry to
touch in about 30 minutes. Thicker coats will take longer to dry. It can be
top-coated in 40-60 minutes, under normal conditions. Peel Bond goes
on white and dries to a hazy, clear. Once it has turned to the hazy, clear, it is
ready to recoat or topcoat. It can be heavily applied, up to 40 mils wet in one
application on a vertical surface, however, many applicators apply a first
application on a vertical surface, however, many applicators apply a first
coat of 15-20 mils to see how the surface looks. They follow with a second coat as required.
Coverage will vary between 50 to 200 square feet per gallon, depending on dry film thickness.
NOTE: Peel Bond is not recommended for horizontal walking surfaces such as decks.
BRUSH:
Synthetic fiber brush designed for latex paints is recommended. Apply thickly.
ROLL:
½ inch nap synthetic fiber roller cover designed for latex
paints. Roll in one direction.
SPRAY:
0.015 to 0.019 tip is recommended and 1200 psi.
Sprays well with most sizes of spray equipment.
Sprays well with most sizes of spray equipment.
Clean Up:
Clean up with soap and water immediately after use.
